Current Luxury Support
Bootsie Chair
The Boostie chair has a built in tensioner on the bottom of the seat that can be reached from a sitting position.
It is available in white or gray. Seats are made from durable UV resistant and legs are made from aircraft grade aluminum. Rivets and fasteners are made of stainless steel and aluminum to prevent rusting.
The Bootsie chair is 14lbs and is made of UV resistant plastic, aircraft grade aluminum, and stainless steel rivets.
Yes, the Bootsie chair is designed to nest with each other. Two Bootsie chairs stacked side by side measure 1-“. If stacking horizontally (in the trunk of your car) you can invert every other Bootsie chair; two Bootsie chairs stack 8” high.
The Bootsie chair seat width measures wq”, 1-3″ wider than most folding chairs. The unfolded Bootsie seat height is 17.5″ off the ground. The Bootsie chairs collapsed measures 25.5″W X 37″H X 25″ D.
No standard cushions are available for Bootsie.
Coming soon is a snap-on cup holder and a shoulder carrying strap.
E-Wand
Yes! The E Wand is fully compatible will all venetian blinds, mini-blinds, and wand tilted vertical blinds. Unfortunately, at this time the E Wand is not compatible with vertical blinds that use a rope or chain to tilt the slats. If you would like to verify your blind’s compatibility, feel free to email us at service@currentluxury.com
Yes! For homes with corded tilt horizontal blinds, we offer a universal conversion kit with adapters to fit any venetian blinds on the market. Converting a cord tilt blind to a wand tilt is a very straightforward process that is outlined in the Installation Manual and User Guide. For the best operation of the E Wand, we highly recommend using our universal conversion kit over the several offered through third party sellers, as the tilt stem is usually positioned differently.
Installation of the E-Wand is straight forward, and programming is intuitive. Download the E Wand Installation Manual and User Guide.
The automation functions of the E-Wand are controlled through a sliding sensor switch. The top switch controls the light sensor and the bottom switch controls the temperature sensor. When the switches are in the top position, they are off. When the switches are positioned in the middle, they are set to fully automatic, meaning the E Wand will both close and open your blind slats. When the switch is in the lowest position, the E Wand is set to semi-automatic, meaning it will only close your blinds, allowing you to manually open them to meet your needs. If you would like your blinds to open automatically as well as close, simply move the sensor switch to the fully automatic (middle) position. Still having trouble? You can send us an email to service@currentluxury.com, or give us a call at 850-435-4994 and we will be happy to help.
Your E Wand is smart, but it cannot tell the time of day. Instead, they detect a change in light. There are two primary reasons why the E Wand may not be closing your blinds at sunset.
1) A manual movement was made within three hours prior to the sun setting. a. After a manual movement has been made, by either twisting the E Wand Twist Handle or by using the remote, a timer is set. This timer prevents the E Wand from making any automated movements for three hours after the manual movement.
2) The E Wand is positioned unusually close to an indoor lighting fixture.
a. In some instances, when a E Wand is positioned unusually close to a lighting fixture such as an overhead light or table lamp, the E Wand sensors will measure that light’s activity instead of the sun’s activity. To fix this, you can turn that E Wand’s sensor switches off and group it to the E Wand whose behavior you would like it to replicate.
If your blinds continues to remain open after sunset, you can email us at service@currentluxury.com or give us a call at 850-435-4994
Windows play a large part in the efficiency of a home. It is recommended that to save energy, homeowners close their blinds when it is warm outside to reduce heat infiltration into the home. During winter months, when daytime temperatures are low, it is recommended that homeowners open their blinds to allow in residual heat from the sun. It is reported that the typical home will cut between 10-15% of their annual energy usage by closing the blinds or curtains during high temperatures, and opening them during daytime cool temperatures. The automated features controlled by light and temperature sensors on the E Wand use this knowledge to reduce the homes energy consumption by automating slat movement.
When the E Wand has low batteries, it will play a short tune when twisted. Be sure to replace your batteries with 1.5v AA Alkaline batteries.
Batteries in the E Wand last approximately a year under normal use.
Absolutely not! You can link a remote to a E Wand whenever you want.
There are several ways you can control the E Wand: 1) manually, 2) by remote control, 3) by twist grouping, and 4) by initiating automated functions. This is different from many other blind motorization devices that offer only a single method of control.
1) To move the slats manually, you can perform a slight twist on the E Wand Twist Handle until the slats reach your desired position.
2) E-Wands can be controlled via remote control. The remote has 5 channels and an all-channel capability, allowing you full control over which blinds you move.
3) Twist Grouping allows you to move a single E Wand to control a designated group of blinds. All E Wands come with the capability to be twist grouped. Instructions on how to create a twist group can be found in the Installation Manual and User Guide as well as within the Instructional Videos.
4) The Smart Technology enabled sensors control the E Wand’s automated functionality. The sensors detect a change in light, opening the slats around sunrise and closing them around sunset. The sensors will also detect temperature, opening the slats during cool days and closing them during warm days.
Need service or have more questions?
Helux Manual Umbrella
Being counterbalanced with the Easy Lift function allows for effortless opening & closing.
The locking handle locks in any position between fully opened and fully closed.
Absolutely! The Helux is supported by a 1½” rust-resistant powder-coated aluminum center tube.
The frame is made of eight 1/2” diameter flexible fiberglass rods for enhanced integrity in high winds.
Need service or have more questions?
Helux Solar Motorized Umbrella
Remove the battery from the housing and push the button on the motor house. Then press and release the button of the back of the remote with a paper clip and then press and release the up button on the remote.
Remove the battery from housing and make sure that the battery is plugged into the motor assembly.
You can reset the umbrella by pressing the button on the back 6 times. This will reset the umbrella from the network. You then can try re identifying the umbrella with the app following instructions on pages six and seven of the programming instructions guide.
No, under normal usage you should not have to change batteries. Batteries that run the motor are recharged by the solar panel located on the top of the umbrella. Average sunlight is in Southern US is more that enough to recharge your batteries.
Expected usage with lights on three hours every day and unlimited open/close. Under these conditions your batteries will never need charging.
Under most conditions storing you Helux Motorized Umbrella means the solar panel will not be exposed the sunlight and not recharge batteries. Allow you Helux Motorized Umbrella one day to recharge the battery pack or remove the battery and plug it into a charger for one hour. All umbrellas include a cover to protect your canopy in storage.
The Helux Motorized Umbrella is programmed to automatically close under gusty wind conditions.
Replace the removable/rechargeable battery pack with a fully charge battery pack, or allow the Solar panel to charge the batteries. Allow one day for the batteries to recharge or remove battery pack and recharge the batteries for one hour.
Optional legless tables come in 30” and 40” diameter. To install the table remove the motorized umbrella by pushing the locking button on the helical shaft. Screw the table onto the base tube. Then return the motorized umbrella to its’ original position.
Yes, because the table screws onto the helix tube have the ability to rotate the table within the height of the tube. Simply rotate the table left or right to adjust the height of the table. No fasteners required.
Need service or have more questions?
Helux Motorized Cafe
Remove the battery from the housing and push the button on the motor house. Then press and release the button of the back of the remote with a paper clip and then press and release the up button on the remote.
Remove the battery from housing and make sure that the battery is plugged into the motor assembly.
You can reset the umbrella by pressing the button on the back 6 times. This will reset the umbrella from the network. You then can try re identifying the umbrella with the app following instructions on pages six and seven of the programming instructions guide.
No, under normal usage you should not have to change batteries. Batteries that run the motor are recharged by the solar panel located on the top of the umbrella. Average sunlight is in Southern US is more that enough to recharge your batteries.
Expected usage with lights on three hours every day and unlimited open/close. Under these conditions your batteries will never need charging.
Under most conditions storing you Helux Motorized Umbrella means the solar panel will not be exposed the sunlight and not recharge batteries. Allow you Helux Motorized Umbrella one day to recharge the battery pack or remove the battery and plug it into a charger for one hour. All umbrellas include a cover to protect your canopy in storage.
The Helux Motorized Umbrella is programmed to automatically close under gusty wind conditions.
Replace the removable/rechargeable battery pack with a fully charge battery pack, or allow the Solar panel to charge the batteries. Allow one day for the batteries to recharge or remove battery pack and recharge the batteries for one hour.
Need service or have more questions?
HELUX TABLE
The Helux table screws to the bottom pole of the Helux outdoor umbrella. To remove, remove the top portion of the Helux umbrella by lifting up while pushing the small pole release button. After the top portion of the umbrella is removed unscrew the table by rotating the entire table about the fixed pole counter clockwise.
The Helux Table is available in white and dark brown.
The HELUX TABLE is made from Durable UV resistant ABS plastic. It should not require any maintenance and can be easily cleaned with a mild detergent. Do not use cleaners containing scraping aggregates. Do not use steel wool to clean the HELUX table.
30″ table weighs 5.5 lbs and the 40″ table weighs 9.5 lbs.
Helux tables come in 30″ diameter and 40″ diameter. They are both 3/4″ thick.
Optional legless tables come in 30” and 40” diameter. To install the table remove the motorized umbrella by pushing the locking button on the helical shaft. Screw the table onto the base tube. Then return the motorized umbrella to its’ original position.
Yes, because the table screws onto the helix tube have the ability to rotate the table within the height of the tube. Simply rotate the table left or right to adjust the height of the table. No fasteners required.
